12/24V 10-100A MPPT PWM Solar Charge Controller Panel Battery Regulator Dual USB

Description

10-100A MPPT Solar Panel Regulator Charge Controller Auto Focus Tracking 12V/24V
Charging Mode: MPPT(30A/40A/60A/100A)
MPPT solar charge controller: Compared with normal solar charge controller, this MPPT controller could increase efficiency by 10%-30%.
Automatic focusing MPPT tracking charging, high charging efficiency, non-stop detection during charging, bidirectional focusing tracking.
Large-screen LCD display, adjustable charging and discharging parameters.
This MPPT controller has perfect SOC function, control charge current, and supply power to the loads.
Prevent the battery from over-charging, over-discharging and reverse charging to solar panels during nights.
How To Use
Q&A
1. Q: How many watts (W) of solar panels can be connected to 30A, and 60A?
A: 10A Within 240W, 20A Within 480W, 30A Within 720W, 40A Within 960W, 50A Within 1200W, 60A within 1440W, 100A Within 1680W
2. Q: Does this controller support lithium batteries?
A: The new controller(MPPT) is available with lead acid and lithium batteries, others not.
3. Q: My solar panel is 36V 200W, can I charge 12V battery?
A: For 12V battery, solar panel working voltage can be between 17V and 23V; For 24V battery, solar panel working voltage can be between 36V and 46V.
Please confirm that the power and Solar panel working voltage the are within this range. If it's too high, it will damage the controller.
4. Q: Can the inverter be connected to the load side of the controller?
A: Please connect the inverter directly to the battery and not to the load terminal of the controller.
5. Q: Does the controller have a requirement for battery capacity?
A: No, as long as the voltage corresponds to it (but the maximum current of the board and the battery capacity should correspond). For example, the current of the solar panel is 5 amps, the battery capacity is preferably 50 AH, the current of the solar panel is 10 A, and the battery capacity is preferably 100 AH. Do not use a large board to charge a small battery, which may be dangerous.
6. Q: How do you connect the solar panels, batteries, and controllers?
A: Please be sure to connect the battery first (to ensure that the battery is fully charged), then connect the solar panel. When disassembling, please remove the solar panel first, then remove the battery, please connect it exactly as this order, otherwise the controller and other components probably damaged.
Others
1. Always keep the battery on fill voltage condition.
2. Prevent the battery from over-charging.
3. Prevent the battery from over-discharging.
4. Prevent the battery from reverse charging to solar panels during nights.
5. Reverse Polarity Protection for Battery
6. Reverse Polarity Protection for Solar Panels
7. When the battery voltage is low, the controller will automatically cut off the load from the system. If the voltage of battery is back to normal and the load will restart working.
8. Thunder protection
9. According to the battery voltage grade, the controller can automatically set charge-off voltage, the load-off voltage, the load- restore voltage. (The parameter is default under 25 condition, locked by the CPU procedure, cannot adjust.)
10. The controller will automatically compensate the temperature of the charging voltage according to the changes of ambient temperature.
Product Specification
Rated voltage: 12/24V
Rated current: 30/40/60/100A
Max. PV voltage: 50V
Max. PV input power: 750W(12V) / 1500W(24V)
Package Included
1 x Solar Panels Battery Charge Controller
1 x User Manual
Charging Mode: MPPT+PWM(10A/30A/60A/80A/100A)
- Advanced maximum power point tracking (MPPT/PWM) technology, the efficiency is not less than 99.5%. High-quality components improve the system performance, and the maximum conversion efficiency is 98%. Super fast tracking speed and guarantee tracking efficiency.
- Large screen LCD display, charge and discharge current display, cumulative power generation and discharge power query, temperature display, light control + delay control; adjustable charge and discharge parameters, with power-off memory and other functions.
- Dual USB output, the maximum current is 2.5A. Equipped with all necessary protection devices, the control parameters of the system are adjustable, easy to set up and operate. Built-in overheating, overcurrent, short circuit, open circuit protection, fault elimination, controller automatic recovery. Two-way MOS tube anti-backflow circuit, high-power charging mode, ultra-low heat.
- Built-in short circuit protection, open circuit protection, reverse connection protection, overload protection. Reverse current protection, low calorific value, with self-recovery function, will not damage the controller.
- Real-time display of temperature, charging current and discharge current. Current autofocus MPPT tracking charging, high charging efficiency, charging process does not stop detection, two-way focus tracking.
Specifications:
Name: LCD screen solar controller
Voltage: DC 12V / 24V
Display: LCD screen
Two Charging Modes: MPPT & PWM
Self-consumption: <10MA
Overcharge protection: 14.4V / 28.8V
Overcharge Float charge: 13.7V / 27.4V
Charge recovery voltage: 12.6V / 25.2V
Over discharge protection: 10.7V / 21.4V
Over discharge recovery: 12.6V / 25.2V
Dual USB output: 5V / 2A (charge mobile phone, iPad, etc.)
Working temperature: -35 -60
12V fits 18V solar panel, 24V fits 36V solar panel
12.0 volt lead acid battery corresponding
The float voltage is set to: 13.6
The recovery discharge voltage is set to: 12.6
The discharge cut-off voltage is set to: 10.7
12.8 volt lithium iron phosphate battery corresponding
The float voltage is set to: 14.6
The recovery discharge voltage is set to: 13.6
The discharge cut-off voltage is set to: 11.0
11.1 volt lithium battery corresponding
The float voltage is set to: 12.6
The recovery discharge voltage is set to: 11.6
The discharge cut-off voltage is set to: 9.6
The minute is adjustable when the output is turned off, which is more convenient (there is no adjustment when the market is only available).
PV system power Description:
10A/30A/60A/80A/100A battery 12V photovoltaic system: power is respectively 100-1000W
10A/30A/60A/80A/100A battery battery 24V photovoltaic system: power is respectively 200-2000W
Package Included:
1X Solar Panels Battery Charge Controller
1X User Manual
Notes:
1. The charge regulator is only suitable for lead-acid batteries: OPEN, AGM, GEL, it is not suited for nickel hydride, lithium, Liions, or other batteries.
2. This controller can only use photovoltaic panels as charging power. Do not use DC or other power as charging power.
3.The LCD display has an error of 0.2 V- 0.3 V, but this is normal
4. Old batteries may be degraded the capacity after hundereds of cycles, easily drop lower than 8V, which results in the controller will be shut off (LCD screen become totally “DEAD”).
5. Indoor use only: the working temperature of this controller is -35°C to +60°C, during hot sunny days, the temperature outside might go up to 60-75°C. Please do keep the controller stay in cool and well-ventilated place to maintain good heat dissipation.
Charging Mode: PWM(30A/60A)
1.Build-in industrial micro controller.
2.Big LCD display,all adjustable controlling parameter of the system.
3.Fully 4-stage PWM charge management.
4.Build-in all necessory protections including short-circuit protection,open-circuit protection,reverse protection,over-load protection.
5.Dual mosfet Reverse current protection ,low heat production
LCD display/key and Operations:
MENU:Switch between different display,or to enter/exit setting by long press.
UP: Press to increase value.
DOWN:Press to decrease value.
System Connection:
1.Connect the battery to the charge regulator - plus and minus.
2.Connect the photovoltaic module to the regulator - plus and minus.
3.Connect the consumer to the charge regulator - plus and minus.
*The reverse order applies when deinstalling!
*An improper sequence order can damage the controller!
Attention:
1.press the [Down] button to ON/OFF load manully at main display.
2.the work mode is working as below:
[24H] load output 24hours
[1-23H] load on after sunset and closed after setting hours
[0H] Dusk to dawn
3.Batteries:Only fit for OPEN, AGM, GEL
4.The charge regulator is only suitable for,regulating solar modules Never connect another charging source to the charge regulator.
5.Please make sure your battery has enough voltage for the controller to recognize the battery type before first installation.
Specifications:
Load: Light Control
MPN: RBL
Charging Mode:PWM
Model: RBL-30A
System Voltage: 12V 24V
Max Solar input(Solar Panel):36V(24V battery) 18V(12V battery)
Max input power: 390W(12V system); 780W(24V system)
Equalization: 12.6V(sealed) 14.2V(Gel) 14.6V(flood)
Float charge: 13.7V(defaul,adjustable)12.0-15.0V
Discharge stop voltage: 10.7V(defaul,adjustable)9.0-11.5V
Discharge reconnect voltage:12.5V(defaul,adjustable)11.0-13.0V
Rated current: 30A
Self-consume:<10mA
Batteries:Only fit for OPEN, AGM, GEL
Operating Temperature:-35~60
USB output:5V/2A Max
Dimension:13.4*7*3.3cm
Package includes:
1x Solar Charge Controller
1x User Manual
Charging Mode: MPPT(30A/50A/70A)
-Automatic Identification System Voltage,12V/24V auto recognition.
-Completed technical data for setup and modify.
- The load control mode can be selected the timer function canbe reset for street light at night.
-Discharge capacity control& Discharge Counter of Ampere Hour.
-Working Storage Function record the total run time of system,Record timers of error during running time record times of full charged battery.
-Solar Panels Battery Solar Charge Controller positive poles areall connected together adopting negative MOSFET in series control circuit.
-LCD display &Double Button Operation :high-definition display device status.
-Dual USB 2.4A fast charging ports, pure copper wiring port with good conductivity.
-Six intelligent safety protection&stable output, rapid operation :Efficiency increased by 30% with high voltage protection, short circuit protection, reverse connection protection, temperature protection, overload protection, low voltage protection.
-Alloy heat dissipation backplane fast heat dissipation: prevent the device from running for a long time to cause the circuit to heat up.
-Widely used: RV solar panel power supply in the car, solar panel large-scale power generation system, solar panel environmental protection street light, yachts and ships.
Specification
Model30A/50A/70A
System Voltage12V/24V
Max Input Voltage of solar panel:55V
Self-consumption≤10mA
Max charge current:30A
Max discharge current:30A
LVD:11.0V ADJ 9V…12V,x2/24V
LVR:12.6V ADJ 11V…13.5V,x2/24V
Float Voltage:13.8V ADJ 13V…15V,x2/24V
Boost charging:14.4V, *2/24V Battery Voltage less than 12V start boost charging 2 hours
Battery Over Voltage:16.5V,×2/24V
Reverse Connection Protection:yes
Load Over Current Protection:Yes each two minutes restart once
Temperature Compensation:-24 mV / for 12V system x2/24V
Working Temperature-20…+55
Waterproof grade:IP32
Size :30A (L*W*H)14*3.5*17cm/5.5*1.38*6.69inch
USB:5V 2.1A
DC output:12V/24V
Current display:None
Package including
1X Charge Controller
1X Manual
Charging Mode: PWM(10A/20A/30A)
✔ Using industrial-grade main control chip, real-time display of working temperature, charging current and discharge current.
✔ Large-screen LCD display, charge and discharge current display, cumulative power generation and discharge power query, temperature display, light control + delay control, adjustable charge and discharge parameters, with power-off memory, etc.
✔ Dual USB output, the maximum current is up to 2.5A, supporting Apple mobile phone charging.
✔ Complete 3-stage charging management, it can effectively protect the battery and make the battery more durable.
✔ Built-in over-current, short-circuit protection, open-circuit protection, and reverse connection protection, all of which are self-recovery, without damaging the controller.
✔ Anti-backflow circuit, ultra-low heat generation, auto focus, high charging efficiency, non-stop detection.
Specification:
Model: K1688
Colour: Black
Material:ABS
System voltage: 12V/24V automatic adaptation
Rated charging current: 10A/20A/30A
Maximum PV voltage: 50V
Maximum PV input power: 130W (12V) 260W (24V)
Boost charging voltage: 14.4V
Float voltage: 13.7V (default, adjustable)
Discharge cut-off voltage: 10.7V (default, adjustable)
Discharge recovery voltage: 12.6V (default, adjustable)
Charging recovery voltage: 13V
Threshold of light-controlled light-on: photovoltaic panel 8V (light-controlled light-on has a delay)
Threshold of light-controlled light-off: photovoltaic panel 8V (light-controlled light-off has a delay)
USB output: 2-way USB output, 5V/2.5A (maximum)
Standby current: <10mA
Working temperature: -35～+60℃
Size: 125*112*34mm/4.92*4.41*1.34inch
Packing size: 13*10.5*3.8cm/5.12*4.13*1.50inch
Package include:
1x Solar Panel Charge Controller
1x User Manual
1x Packing Box
Payments
Delivery details
Return and exchange
Feedback & Rating
Contact us
Payments
Payments: Paypal, Google Pay, Visa, Master Card, Amerian Express, Discover.
Delivery details
All items are shipped from
US
warehouse located at
NJ
. We ship to your eBay or Paypal address. Please make sure your eBay or Paypal address is correct before you pay.
Return and exchange
Free return
Feedback & Rating
Pls contact our customer service firstly if have any problems , we will help to solve the issue, and could offer free return service for full refund or free replacement after confirming. You can buy from us with confidence
Contact us
If have any problems, please feel free to contact us.